Note: you can right-click on any of the pictures below and choose View Image to get a larger/more detailed photo; use your browser's Back button to return to the main blog.

There were a few things I never got to do before I had to vacate the basement (a friend’s, not my own) where I built the instrument.  Chief among these was putting on the gold bands that are traditional decoration for a French-style harpsichord, along with gilding the case moldings.  (Yes, we use real gold leaf.)  There were a few other cosmetic issues that needed taking care of also.

The photo above shows the instrument after it came back home on December 6, with the gold bands.  (Please ignore the mess in the parlor — woodwork refinishing in progress.)

Below is a view of the keywell, with newly gilded moldings visible.  You can also see the new music desk.

The original music desk is a folding design that fits inside the closed instrument; a clever use of space, but it is too small and insecure to hold a large book and the top section tends to slip down without warning:

Plectra (the little horizontal things that pluck the strings) harden with age, so it was time for re-quilling.  (We use the term ‘quilling’ even if the plectra are made of plastic rather than bird quill as was done in the Baroque era — although some people today do use actual quills.)  Strings don’t last forever either; I could have put off re-stringing for a while, but now we have access to better wire than was available 30 years ago, so I decided to have it re-strung along with the revoicing.   Here is some of the historical music wire that Anne installed (‘Nuremberg’ refers to a system of wire measurement used in the 18th century):

I decided to replace the jacks (the vertical pieces that rise up when a key is pressed and cause the plectra to pluck the strings).  The jacks that came with the kit were made of plastic; these eventually deform (although mine had not yet done so), and replacements in the original style will probably not be available in the future. This was not part of my original plan, and it added considerable complexity and cost to the project, but I think it was worth doing.  Here is one of the original plastic jacks next to one of the new pearwood ones.  The new jacks, made by a gentleman on the west coast who specializes in this work, are works of art and made to very exacting specifications.

This harpsichord has three sets of strings and four sets of jacks, as you can see in the next photo.  The fourth (rightmost) set of jacks plucks the same set of strings as the third set, but has plectra of soft leather instead of plastic.

The jacks live in a gap between the soundboard and the pinblock.  To keep the gap from closing up under the tension of the strings, there are three spacers.  The original spacers were made of wood and had begun to deform under pressure; Anne replaced them with iron ones.

Here is a closeup of the plectra, two in plastic and one in leather:

The instrument now sounds and feels wonderful to play! The historical wire produces a tone with more fundamental than modern wire.  (The sound of any harpsichord has more overtones in comparison with that of a piano, and poor-quality wire or poor voicing can result in an overly bright effect.  So more fundamental is good.)  The result is definitely worth the wait — almost a year until Anne had an opening in her schedule — as well as the cost!  I don't have equipment to make a decent recording of it, but its sound has a definite family resemblance to a wonderful harpsichord made in Paris by Henri Hemsch in 1756.  Here is a link to Mireille Lagacé playing the harpsichord suites of Joseph Bodin de Boismortier on the Hemsch; listen on some decent speakers or headphones, not earbuds.  I suggest the second suite, which begins at 25:07.

Here's the leftover slate in my garage.  It's not likely that any repairs will be needed while I own the house, but I will leave it for future owners.

Here are some shots of the final result (zoom in for a closer look).  The east side:

The southwest from across the street:

The northwest corner:

Here you can see the complete gutter repairs, with the black EPDM membrane, the 2 x 4, and the raised outer edging.  (Sorry about the roll of tape!)

The bottom of the copper edging is angled out and extends a little below the top of the crown molding.  This should prevent water from getting behind the molding as happened in several spots with the original gutters.

My contractor finally got me the photos they took on the roof, so I added some here.  This is a complicated roof.  The chimney emerges just to the east of the main ridgeline.  In this photo you can see the intersection of the ridge rolls and the chimney flashing.

Looking down on the west reverse gable--nice view of the slate as well as the copper:

The northwest corner.  Notice the the Yankee gutter at the center right.  At the bottom you can see the cleat into which the ridge roll is fitted.  Using cleats, rather than fastening the ridge caps directly to the roof, is the preferable method.

The first ridge roll went on the SE.  Note also the cleats at the top of the gable that will hold the ridge roll.

Here they are on the northwest corner.

In the two photos above, notice that the slate does not come all the way down to the gutter; the black EPDM membrane is visible even from the ground.  I recalled that in the old roof the slate came down one more course.  I asked my contractor about this.  He said that's how they did it back in the day, but that now it's considered better to keep the slate a little further up to avoid any problems when snow or ice sits in the gutter.  (The EPDM goes up 3' or so under the slate.)  I prefer the original look, but avoiding water problems is certainly a Good Thing.  My contractor also said that it would not be difficult to line the gutters with copper if I really don't like seeing the EPDM.  (Let's not get carried away here . . . )

They did some additional work on the gutters (apparently this was not all done), putting copper flashing on the gable edges, and on setting up cleats to hold the ridge roll.  All stuff that had to be done, but not photogenic, so no new pictures today (Monday).

No work on Tuesday, due to chance of rain (which did not materialize).

Notice the shiny copper edging on the south gable (left in the photo); first time I've seen that installed so far.

Here are some tiles stacked next to the lift they use to take slate up to the roof:

And here's the northwest corner all done: